 Everipedia is now IQ.wiki - Join the IQ Brainlist and our Discord for early access to editing on the new platform and to participate in the beta testing. # Decibel

dBPower ratioAmplitude ratio
10010000000000100000
90100000000031623
8010000000010000
70100000003162
6010000001000
50100000316.2
4010000100
30100031.62
2010010
10103.162
63.981 ≈ 41.995 ≈ 2
31.995 ≈ 21.413 ≈2
11.2591.122
011
−10.7940.891
−30.501 ≈ ​120.708 ≈12
−60.251 ≈ ​140.501 ≈ ​12
−100.10.3162
−200.010.1
−300.0010.03162
−400.00010.01
−500.000010.003162
−600.0000010.001
−700.00000010.0003162
−800.000000010.0001
−900.0000000010.00003162
−1000.00000000010.00001
An example scale showing power ratios x, amplitude ratiosx, and dB equivalents 10 log10x.

The decibel (symbol: dB) is a unit of measurement used to express the ratio of one value of a power or field quantity to another on a logarithmic scale, the logarithmic quantity being called the power level or field level, respectively. It can be used to express a change in value (e.g., +1 dB or −1 dB) or an absolute value. In the latter case, it expresses the ratio of a value to a fixed reference value; when used in this way, a suffix that indicates the reference value is often appended to the decibel symbol. For example, if the reference value is 1 volt, then the suffix is "V" (e.g., "20 dBV"), and if the reference value is one milliwatt, then the suffix is "m" (e.g., "20 dBm").

Two different scales are used when expressing a ratio in decibels, depending on the nature of the quantities: power and field (root-power). When expressing a power ratio, the number of decibels is ten times its logarithm to base 10. That is, a change in power by a factor of 10 corresponds to a 10 dB change in level. When expressing field (root-power) quantities, a change in amplitude by a factor of 10 corresponds to a 20 dB change in level. The decibel scales differ by a factor of two so that the related power and field levels change by the same number of decibels with linear loads.

The definition of the decibel is based on the measurement of power in telephony of the early 20th century in the Bell System in the United States. One decibel is one tenth (deci-) of one bel, named in honor of Alexander Graham Bell; however, the bel is seldom used. Today, the decibel is used for a wide variety of measurements in science and engineering, most prominently in acoustics, electronics, and control theory. In electronics, the gains of amplifiers, attenuation of signals, and signal-to-noise ratios are often expressed in decibels.

In the International System of Quantities, the decibel is defined as a unit of measurement for quantities of type level or level difference, which are defined as the logarithm of the ratio of power- or field-type quantities.

## History

The decibel originates from methods used to quantify signal loss in telegraph and telephone circuits. The unit for loss was originally Miles of Standard Cable (MSC). 1 MSC corresponded to the loss of power over a 1 mile (approximately 1.6 km) length of standard telephone cable at a frequency of 5000 radians per second (795.8 Hz), and matched closely the smallest attenuation detectable to the average listener. The standard telephone cable implied was "a cable having uniformly distributed resistance of 88 Ohms per loop-mile and uniformly distributed shunt capacitance of 0.054 microfarads per mile" (approximately corresponding to 19 gauge wire).

In 1924, Bell Telephone Laboratories received favorable response to a new unit definition among members of the International Advisory Committee on Long Distance Telephony in Europe and replaced the MSC with the Transmission Unit (TU). 1 TU was defined such that the number of TUs was ten times the base-10 logarithm of the ratio of measured power to a reference power. The definition was conveniently chosen such that 1 TU approximated 1 MSC; specifically, 1 MSC was 1.056 TU. In 1928, the Bell system renamed the TU into the decibel, being one tenth of a newly defined unit for the base-10 logarithm of the power ratio. It was named the bel, in honor of the telecommunications pioneer Alexander Graham Bell. The bel is seldom used, as the decibel was the proposed working unit.

The naming and early definition of the decibel is described in the NBS Standard's Yearbook of 1931:

Since the earliest days of the telephone, the need for a unit in which to measure the transmission efficiency of telephone facilities has been recognized. The introduction of cable in 1896 afforded a stable basis for a convenient unit and the "mile of standard" cable came into general use shortly thereafter. This unit was employed up to 1923 when a new unit was adopted as being more suitable for modern telephone work. The new transmission unit is widely used among the foreign telephone organizations and recently it was termed the "decibel" at the suggestion of the International Advisory Committee on Long Distance Telephony. The decibel may be defined by the statement that two amounts of power differ by 1 decibel when they are in the ratio of 100.1 and any two amounts of power differ by N decibels when they are in the ratio of 10N(0.1). The number of transmission units expressing the ratio of any two powers is therefore ten times the common logarithm of that ratio. This method of designating the gain or loss of power in telephone circuits permits direct addition or subtraction of the units expressing the efficiency of different parts of the circuit ...

In 1954, J. W. Horton argued that the use of the decibel as a unit for quantities other than transmission loss led to confusion, and suggested the name 'logit' for "standard magnitudes which combine by addition".

In April 2003, the International Committee for Weights and Measures (CIPM) considered a recommendation for the inclusion of the decibel in the International System of Units (SI), but decided against the proposal. However, the decibel is recognized by other international bodies such as the International Electrotechnical Commission (IEC) and International Organization for Standardization (ISO). The IEC permits the use of the decibel with field quantities as well as power and this recommendation is followed by many national standards bodies, such as NIST, which justifies the use of the decibel for voltage ratios. The term field quantity is deprecated by ISO 80000-1, which favors root-power. In spite of their widespread use, suffixes (such as in dBA or dBV) are not recognized by the IEC or ISO.

## Definition

ISO 80000-3 describes definitions for quantities and units of space and time. The decibel for use in acoustics is defined in ISO 80000-8. The major difference from the article below is that for acoustics the decibel has no absolute value.

The ISO Standard 80000-3:2006 defines the following quantities. The decibel (dB) is one-tenth of a bel: 1 dB = 0.1 B. The bel (B) is ​1⁄2 ln(10) nepers: 1 B = ​1⁄2 ln(10) Np. The neper is the change in the level of a field quantity when the field quantity changes by a factor of e, that is 1 Np = ln(e) = 1, thereby relating all of the units as nondimensional natural log of field-quantity ratios, 1 dB = 0.11513… Np = 0.11513…. Finally, the level of a quantity is the logarithm of the ratio of the value of that quantity to a reference value of the same kind of quantity.

Therefore, the bel represents the logarithm of a ratio between two power quantities of 10:1, or the logarithm of a ratio between two field quantities of √10:1.

Two signals whose levels differ by one decibel have a power ratio of 101/10, which is approximately 1.25893, and an amplitude (field quantity) ratio of 10​1⁄20 (1.12202).

The bel is rarely used either without a prefix or with SI unit prefixes other than deci; it is preferred, for example, to use hundredths of a decibel rather than millibels. Thus, five one-thousandths of a bel would normally be written '0.05 dB', and not '5 mB'.

The method of expressing a ratio as a level in decibels depends on whether the measured property is a power quantity or a root-power quantity; see Field, power, and root-power quantities for details.

### Power quantities

When referring to measurements of power quantities, a ratio can be expressed as a level in decibels by evaluating ten times the base-10 logarithm of the ratio of the measured quantity to reference value. Thus, the ratio of P (measured power) to P0 (reference power) is represented by L**P, that ratio expressed in decibels, which is calculated using the formula: The base-10 logarithm of the ratio of the two power quantities is the number of bels. The number of decibels is ten times the number of bels (equivalently, a decibel is one-tenth of a bel). P and P0 must measure the same type of quantity, and have the same units before calculating the ratio. If P = P0 in the above equation, then L**P = 0. If P is greater than P0 then L**P is positive; if P is less than P0 then L**P is negative.

Rearranging the above equation gives the following formula for P in terms of P0 and L**P: ### Field quantities and root-power quantities

When referring to measurements of field quantities, it is usual to consider the ratio of the squares of F (measured field) and F0 (reference field). This is because in most applications power is proportional to the square of field, and historically their definitions were formulated to give the same value for relative ratios in such typical cases. Thus, the following definition is used: The formula may be rearranged to give Similarly, in electrical circuits, dissipated power is typically proportional to the square of voltage or current when the impedance is constant. Taking voltage as an example, this leads to the equation for power gain level L**G: where Vout is the root-mean-square (rms) output voltage, Vin is the rms input voltage. A similar formula holds for current.

The term root-power quantity is introduced by ISO Standard 80000-1:2009 as a substitute of field quantity. The term field quantity is deprecated by that standard.

### Relationship between power level and field level

Although power and field quantities are different quantities, their respective levels are historically measured in the same units, typically decibels. A factor of 2 is introduced to make changes in the respective levels match under restricted conditions such as when the medium is linear and the same waveform is under consideration with changes in amplitude, or the medium impedance is linear and independent of both frequency and time. This relies on the relationship holding. In a nonlinear system, this relationship does not hold by the definition of linearity. However, even in a linear system in which the power quantity is the product of two linearly related quantities (e.g. voltage and current), if the impedance is frequency- or time-dependent, this relationship does not hold in general, for example if the energy spectrum of the waveform changes.

For differences in level, the required relationship is relaxed from that above to one of proportionality (i.e., the reference quantities P0 and F0 need not be related), or equivalently, must hold to allow the power level difference to be equal to the field level difference from power P1 and V1 to P2 and V2. An example might be an amplifier with unity voltage gain independent of load and frequency driving a load with a frequency-dependent impedance: the relative voltage gain of the amplifier is always 0 dB, but the power gain depends on the changing spectral composition of the waveform being amplified. Frequency-dependent impedances may be analyzed by considering the quantities power spectral density and the associated field quantities via the Fourier transform, which allows elimination of the frequency dependence in the analysis by analyzing the system at each frequency independently.

### Conversions

Since logarithm differences measured in these units are used to represent power ratios and field ratios, the values of the ratios represented by each unit are also included in the table.

Conversion between units of level and a list of corresponding ratios
UnitIn decibelsIn belsIn nepersPower ratioField ratio
1 dB1 dB0.1 B0.11513 Np10110≈ 1.2589310120≈ 1.12202
1 Np8.68589 dB0.868589 B1 Npe2≈ 7.38906e ≈ 2.71828
1 B10 dB1 B1.1513 Np101012≈ 3.16228

### Examples

The unit dBW is often used to denote a ratio for which the reference is 1 W, and similarly dBm for a 1 mW reference point.

• Calculating the ratio in decibels of 1 kW (one kilowatt, or 1000 watts) to 1 W yields: • The ratio in decibels of √1000 V ≈ 31.62 V to 1 V is (31.62 V / 1 V)2 ≈ 1 kW / 1 W, illustrating the consequence from the definitions above that L**G has the same value, 30 dB, regardless of whether it is obtained from powers or from amplitudes, provided that in the specific system being considered power ratios are equal to amplitude ratios squared.

• The ratio in decibels of 1 mW (one milliwatt) to 10 W is obtained with the formula • The power ratio corresponding to a 3 dB change in level is given by A change in power ratio by a factor of 10 corresponds to a change in level of 10 dB. A change in power ratio by a factor of 2 or ​1⁄2 is approximately a change of 3 dB. More precisely, the change is ±3.0103 dB, but this is almost universally rounded to "3 dB" in technical writing. This implies an increase in voltage by a factor of √2 ≈ 1.4142. Likewise, a doubling or halving of the voltage, and quadrupling or quartering of the power, is commonly described as "6 dB" rather than ±6.0206 dB.

Should it be necessary to make the distinction, the number of decibels is written with additional significant figures. 3.000 dB is a power ratio of 10​3⁄10, or 1.9953, about 0.24% different from exactly 2, and a voltage ratio of 1.4125, 0.12% different from exactly √2. Similarly, an increase of 6.000 dB is the power ratio is 10​6⁄10 ≈ 3.9811, about 0.5% different from 4.

## Properties

The decibel is useful for representing large ratios and for simplifying representation of multiplied effects such as attenuation from multiple sources along a signal chain. Its application in systems with additive effects is less intuitive.

### Reporting large ratios

The logarithmic scale nature of the decibel means that a very large range of ratios can be represented by a convenient number, in a manner similar to scientific notation. This allows one to clearly visualize huge changes of some quantity. See Bode plot and Semi-log plot. For example, 120 dB SPL may be clearer than "a trillion times more intense than the threshold of hearing".

### Representation of multiplication operations

Level values in decibels can be added instead of multiplying the underlying power values, which means that the overall gain of a multi-component system, such as a series of amplifier stages, can be calculated by summing the gains in decibels of the individual components, rather than multiply the amplification factors; that is, log(A × B × C) = log(A) + log(B) + log(C). Practically, this means that, armed only with the knowledge that 1 dB is a power gain of approximately 26%, 3 dB is approximately 2× power gain, and 10 dB is 10× power gain, it is possible to determine the power ratio of a system from the gain in dB with only simple addition and multiplication. For example:

• A system consists of 3 amplifiers in series, with gains (ratio of power out to in) of 10 dB, 8 dB, and 7 dB respectively, for a total gain of 25 dB. Broken into combinations of 10, 3, and 1 dB, this is: 25 dB = 10 dB + 10 dB + 3 dB + 1 dB + 1 dB With an input of 1 watt, the output is approximately 1 W × 10 × 10 × 2 × 1.26 × 1.26 ≈ 317.5 W Calculated exactly, the output is 1 W × 10​25⁄10 = 316.2 W. The approximate value has an error of only +0.4% with respect to the actual value, which is negligible given the precision of the values supplied and the accuracy of most measurement instrumentation.

However, according to its critics, the decibel creates confusion, obscures reasoning, is more related to the era of slide rules than to modern digital processing, and is cumbersome and difficult to interpret.

According to Mitschke, "The advantage of using a logarithmic measure is that in a transmission chain, there are many elements concatenated, and each has its own gain or attenuation. To obtain the total, addition of decibel values is much more convenient than multiplication of the individual factors." However, for the same reason that humans excel at additive operation over multiplication, decibels are awkward in inherently additive operations: "if two machines each individually produce a sound pressure level of, say, 90 dB at a certain point, then when both are operating together we should expect the combined sound pressure level to increase to 93 dB, but certainly not to 180 dB!"; "suppose that the noise from a machine is measured (including the contribution of background noise) and found to be 87 dBA but when the machine is switched off the background noise alone is measured as 83 dBA. [...] the machine noise [level (alone)] may be obtained by 'subtracting' the 83 dBA background noise from the combined level of 87 dBA; i.e., 84.8 dBA."; "in order to find a representative value of the sound level in a room a number of measurements are taken at different positions within the room, and an average value is calculated. [...] Compare the logarithmic and arithmetic averages of [...] 70 dB and 90 dB: logarithmic average = 87 dB; arithmetic average = 80 dB."

Addition on a logarithmic scale is called logarithmic addition, and can be defined by taking exponentials to convert to a linear scale, adding there, and then taking logarithms to return. For example, where operations on decibels are logarithmic addition/subtraction and logarithmic multiplication/division, while operations on the linear scale are the usual operations:  Note that the logarithmic mean is obtained from the logarithmic sum by subtracting , since logarithmic division is linear subtraction.

Quantities in decibels are not necessarily additive, thus being "of unacceptable form for use in dimensional analysis".

## Uses

### Perception

The human perception of the intensity of sound and light approximates the logarithm of intensity rather than a linear relationship (Weber–Fechner law), making the dB scale a useful measure.

### Acoustics

The decibel is commonly used in acoustics as a unit of sound pressure level. The reference pressure for sound in air is set at the typical threshold of perception of an average human and there are common comparisons used to illustrate different levels of sound pressure. Sound pressure is a field quantity, therefore the field version of the unit definition is used: where prms is the root mean square of the measured sound pressure and pref is the standard reference sound pressure of 20 micropascals in air or 1 micropascal in water.

Use of the decibel in underwater acoustics leads to confusion, in part because of this difference in reference value.

The human ear has a large dynamic range in sound reception. The ratio of the sound intensity that causes permanent damage during short exposure to that of the quietest sound that the ear can hear is greater than or equal to 1 trillion (1012). Such large measurement ranges are conveniently expressed in logarithmic scale: the base-10 logarithm of 1012 is 12, which is expressed as a sound pressure level of 120 dB re 20 μPa.

Since the human ear is not equally sensitive to all sound frequencies, noise levels at maximum human sensitivity, somewhere between 2 and 4 kHz, are factored more heavily into some measurements using frequency weighting. (See also Stevens' power law.)

The main instrument used for measuring sound levels in the environment and in the workplace is the Sound Level Meter. Most sound level meters provide readings in A, C, and Z-weighted decibels and must meet international standards such as IEC 61672-2013.

### Electronics

In electronics, the decibel is often used to express power or amplitude ratios (as for gains) in preference to arithmetic ratios or percentages. One advantage is that the total decibel gain of a series of components (such as amplifiers and attenuators) can be calculated simply by summing the decibel gains of the individual components. Similarly, in telecommunications, decibels denote signal gain or loss from a transmitter to a receiver through some medium (free space, waveguide, coaxial cable, fiber optics, etc.) using a link budget.

The decibel unit can also be combined with a reference level, often indicated via a suffix, to create an absolute unit of electric power. For example, it can be combined with "m" for "milliwatt" to produce the "dBm". A power level of 0 dBm corresponds to one milliwatt, and 1 dBm is one decibel greater (about 1.259 mW).

In professional audio specifications, a popular unit is the dBu. This is relative to the root mean square voltage which delivers 1 mW (0 dBm) into a 600-ohm resistor, or √1 mW×600 Ω ≈ 0.775 VRMS. When used in a 600-ohm circuit (historically, the standard reference impedance in telephone circuits), dBu and dBm are identical.

### Optics

In an optical link, if a known amount of optical power, in dBm (referenced to 1 mW), is launched into a fiber, and the losses, in dB (decibels), of each component (e.g., connectors, splices, and lengths of fiber) are known, the overall link loss may be quickly calculated by addition and subtraction of decibel quantities.

In spectrometry and optics, the blocking unit used to measure optical density is equivalent to −1 B.

### Video and digital imaging

In connection with video and digital image sensors, decibels generally represent ratios of video voltages or digitized light intensities, using 20 log of the ratio, even when the represented intensity (optical power) is directly proportional to the voltage generated by the sensor, not to its square, as in a CCD imager where response voltage is linear in intensity. Thus, a camera signal-to-noise ratio or dynamic range quoted as 40 dB represents a ratio of 100:1 between optical signal intensity and optical-equivalent dark-noise intensity, not a 10,000:1 intensity (power) ratio as 40 dB might suggest. Sometimes the 20 log ratio definition is applied to electron counts or photon counts directly, which are proportional to sensor signal amplitude without the need to consider whether the voltage response to intensity is linear.

However, as mentioned above, the 10 log intensity convention prevails more generally in physical optics, including fiber optics, so the terminology can become murky between the conventions of digital photographic technology and physics. Most commonly, quantities called "dynamic range" or "signal-to-noise" (of the camera) would be specified in 20 log dB, but in related contexts (e.g. attenuation, gain, intensifier SNR, or rejection ratio) the term should be interpreted cautiously, as confusion of the two units can result in very large misunderstandings of the value.

Photographers typically use an alternative base-2 log unit, the stop, to describe light intensity ratios or dynamic range.

## Suffixes and reference values

Suffixes are commonly attached to the basic dB unit in order to indicate the reference value by which the ratio is calculated. For example, dBm indicates power measurement relative to 1 milliwatt.

In cases where the unit value of the reference is stated, the decibel value is known as "absolute". If the unit value of the reference is not explicitly stated, as in the dB gain of an amplifier, then the decibel value is considered relative.

The SI does not permit attaching qualifiers to units, whether as suffix or prefix, other than standard SI prefixes. Therefore, even though the decibel is accepted for use alongside SI units, the practice of attaching a suffix to the basic dB unit, forming compound units such as dBm, dBu, dBA, etc., is not. The proper way, according to the IEC 60027-3, is either as L**x (re xref) or as L**x/xref, where x is the quantity symbol and xref is the value of the reference quantity, e.g., L**E (re 1 μV/m) = L**E/(1 μV/m) for the electric field strength E relative to 1 μV/m reference value.

Outside of documents adhering to SI units, the practice is very common as illustrated by the following examples. There is no general rule, with various discipline-specific practices. Sometimes the suffix is a unit symbol ("W","K","m"), sometimes it is a transliteration of a unit symbol ("uV" instead of μV for microvolt), sometimes it is an acronym for the unit's name ("sm" for square meter, "m" for milliwatt), other times it is a mnemonic for the type of quantity being calculated ("i" for antenna gain with respect to an isotropic antenna, "λ" for anything normalized by the EM wavelength), or otherwise a general attribute or identifier about the nature of the quantity ("A" for A-weighted sound pressure level). The suffix is often connected with a hyphen, as in "dB‑Hz", or with a space, as in "dB HL", or with no intervening character, as in "dBm", or enclosed in parentheses, as in "dB(sm)".

### Voltage

Since the decibel is defined with respect to power, not amplitude, conversions of voltage ratios to decibels must square the amplitude, or use the factor of 20 instead of 10, as discussed above.

dBVdB(VRMS) –voltagerelative to 1 volt, regardless of impedance. This is used to measure microphone sensitivity, and also to specify the consumerline-levelof−10 dBV, in order to reduce manufacturing costs relative to equipment using a+4 dBuline-level signal.
dBu or dBvRMSvoltagerelative to .AnRMSvoltage of 1 V therefore corresponds to Originally dBv, it was changed to dBu to avoid confusion with dBV. The "v" comes from "volt", while "u" comes from the volume unit used in theVU meter. dBu can be used as a measure of voltage, regardless of impedance, but is derived from a 600 Ω load dissipating 0 dBm (1 mW). The reference voltage comes from the computation .
Inprofessional audio, equipment may be calibrated to indicate a "0" on the VU meters some finite time after a signal has been applied at an amplitude of+4 dBu. Consumer equipment typically uses a lower "nominal" signal level of−10 dBV. Therefore, many devices offer dual voltage operation (with different gain or "trim" settings) for interoperability reasons. A switch or adjustment that covers at least the range between+4 dBuand−10 dBVis common in professional equipment.
dBu0sDefined by Recommendation ITU-R V.574.
dBm0sDefined by Recommendation ITU-R V.574.; dBmV: dB(mVRMS) –voltagerelative to 1 millivolt across 75 Ω. Widely used incable televisionnetworks, where the nominal strength of a single TV signal at the receiver terminals is about 0 dBmV. Cable TV uses 75 Ω coaxial cable, so 0 dBmV corresponds to −78.75 dBW (−48.75 dBm) or approximately 13 nW.
dBμV or dBuVdB(μVRMS) –voltagerelative to 1 microvolt. Widely used in television and aerial amplifier specifications. 60 dBμV = 0 dBmV.

### Acoustics

Probably the most common usage of "decibels" in reference to sound level is dB SPL, sound pressure level referenced to the nominal threshold of human hearing: The measures of pressure (a field quantity) use the factor of 20, and the measures of power (e.g. dB SIL and dB SWL) use the factor of 10.

dB SPLdB SPL (sound pressure level) – for sound in air and other gases, relative to 20 micropascals (μPa), or2×10−5 Pa, approximately the quietest sound a human can hear. Forsound in waterand other liquids, a reference pressure of 1 μPa is used.
An RMS sound pressure of one pascal corresponds to a level of 94 dB SPL.dB SILdBsound intensity level– relative to 10−12 W/m², which is roughly thethreshold of human hearingin air.dB SWLdBsound power level– relative to 10−12 W.dBA, dBB, and dBCThese symbols are often used to denote the use of differentweighting filters, used to approximate the human ear'sresponseto sound, although the measurement is still in dB (SPL). These measurements usually refer to noise and its effects on humans and other animals, and they are widely used in industry while discussing noise control issues, regulations and environmental standards. Other variations that may be seen are dBAordB(A). According to ANSI standards, the preferred usage is to write LA = x dB. Nevertheless, the units dBA and dB(A) are still commonly used as a shorthand for A‑weighted measurements. ComparedBc, used in telecommunications.dB HLdB hearing level is used inaudiogramsas a measure of hearing loss. The reference level varies with frequency according to aminimum audibility curveas defined in ANSI and other standards, such that the resulting audiogram shows deviation from what is regarded as 'normal' hearing.dB Qsometimes used to denote weighted noise level, commonly using theITU-R 468 noise weightingdBpprelative to the peak to peak sound pressure.dBGG‑weighted spectrum

### Audio electronics

dBmdB(mW) – power relative to 1 milliwatt. In audio and telephony, dBm is typically referenced relative to a 600 Ω impedance, which corresponds to a voltage level of 0.775 volts or 775 millivolts.dBm0Power in dBm (described above) measured at azero transmission level point.dBFSdB(full scale) – theamplitudeof a signal compared with the maximum which a device can handle beforeclippingoccurs. Full-scale may be defined as the power level of a full-scalesinusoidor alternatively a full-scalesquare wave. A signal measured with reference to a full-scale sine-wave appears 3 dB weaker when referenced to a full-scale square wave, thus: 0 dBFS(fullscale sine wave) = −3 dBFS(fullscale square wave).dBVUdB volume unitdBTPdB(true peak) –peak amplitudeof a signal compared with the maximum which a device can handle before clipping occurs. In digital systems, 0 dBTP would equal the highest level (number) the processor is capable of representing. Measured values are always negative or zero, since they are less than or equal to full-scale.

dBZdB(Z) – decibel relative to Z = 1 mm6⋅m−3: energy of reflectivity (weather radar), related to the amount of transmitted power returned to the radar receiver. Values above 20 dBZ usually indicate falling precipitation.dBsmdB(m²) – decibel relative to one square meter: measure of theradar cross section(RCS) of a target. The power reflected by the target is proportional to its RCS. "Stealth" aircraft and insects have negative RCS measured in dBsm, large flat plates or non-stealthy aircraft have positive values.

### Radio power, energy, and field strength

dBcrelative to carrier – intelecommunications, this indicates the relative levels of noise or sideband power, compared with the carrier power. Compare dBC, used in acoustics.dBpprelative to the maximum value of the peak power.dBJenergy relative to 1 joule. 1 joule = 1 watt second = 1 watt per hertz, sopower spectral densitycan be expressed in dBJ.dBmdB(mW) – power relative to 1 milliwatt. In the radio field, dBm is usually referenced to a 50 Ω load, with the resultant voltage being 0.224 volts.dBμV/m, dBuV/m, or dBμ dB(μV/m) –electric field strengthrelative to 1 microvoltpermeter. The unit is often used to specify the signal strength of atelevisionbroadcastat a receiving site (the signal measured at the antenna output is reported in dBμV).dBfdB(fW) – power relative to 1 femtowatt.dBWdB(W) – power relative to 1 watt.dBkdB(kW) – power relative to 1 kilowatt.dBedB electrical.dBodB optical. A change of 1 dBo in optical power can result in a change of up to 2 dBe in electrical signal power in a system that is thermal noise limited.

### Antenna measurements

dBidB(isotropic) – the forwardgain of an antennacompared with the hypotheticalisotropic antenna, which uniformly distributes energy in all directions.Linear polarizationof the EM field is assumed unless noted otherwise.dBddB(dipole) – the forward gain of anantennacompared with a half-wavedipole antenna. 0 dBd = 2.15 dBidBiCdB(isotropic circular) – the forward gain of an antenna compared to acircularly polarizedisotropic antenna. There is no fixed conversion rule between dBiC and dBi, as it depends on the receiving antenna and the field polarization.dBqdB(quarterwave) – the forward gain of an antenna compared to a quarter wavelength whip. Rarely used, except in some marketing material. 0 dBq = −0.85 dBidBsmdB(m²) – decibel relative to one square meter: measure of theantenna effective area.dBm−1dB(m−1) – decibel relative to reciprocal of meter: measure of theantenna factor.

### Other measurements

dB‑HzdB(Hz) – bandwidth relative to one hertz. E.g., 20 dB‑Hz corresponds to a bandwidth of 100 Hz. Commonly used inlink budgetcalculations. Also used incarrier-to-noise-density ratio(not to be confused withcarrier-to-noise ratio, in dB).dBov or dBOdB(overload) – theamplitudeof a signal (usually audio) compared with the maximum which a device can handle beforeclippingoccurs. Similar to dBFS, but also applicable to analog systems. According to ITU-T Rec. G.100.1 the level in dBov of a digital system is defined as: ,
with the maximum signal power , for a rectangular signal with the maximum amplitude . The level of a tone with a digital amplitude (peak value) of is therefore .dBrdB(relative) – simply a relative difference from something else, which is made apparent in context. The difference of a filter's response to nominal levels, for instance.dBrndB abovereference noise. See also dBrnCdBrnCdBrnC represents an audio level measurement, typically in a telephone circuit, relative to thecircuit noise level, with the measurement of this level frequency-weighted by a standard C-message weighting filter. The C-message weighting filter was chiefly used in North America. The Psophometric filter is used for this purpose on international circuits. SeePsophometric weightingto see a comparison of frequency response curves for the C-message weighting and Psophometric weighting filters.dBKdB(K) – decibels relative to 1 K; used to expressnoise temperature.dB/KdB(K−1) – decibels relative to 1 K−1. — not decibels per kelvin: Used for the *G/T
• factor, a
figure of meritutilized insatellite communications, relating theantenna gainG to thereceiversystem noise equivalent temperature T.

### List of suffixes in alphabetical order

#### Unpunctuated suffixes

dBAsee dB(A).
dBBsee dB(B).dBcrelative to carrier – intelecommunications, this indicates the relative levels of noise or sideband power, compared with the carrier power.dBCsee dB(C).dBddB(dipole) – the forward gain of anantennacompared with a half-wavedipole antenna. 0 dBd = 2.15 dBidBedB electrical.dBfdB(fW) – power relative to 1femtowatt.dBFSdB(full scale) – theamplitudeof a signal compared with the maximum which a device can handle beforeclippingoccurs. Full-scale may be defined as the power level of a full-scalesinusoidor alternatively a full-scalesquare wave. A signal measured with reference to a full-scale sine-wave appears 3 dB weaker when referenced to a full-scale square wave, thus: 0 dBFS(fullscale sine wave) = −3 dBFS(fullscale square wave).dBGG-weighted spectrumdBidB(isotropic) – the forwardgain of an antennacompared with the hypotheticalisotropic antenna, which uniformly distributes energy in all directions.Linear polarizationof the EM field is assumed unless noted otherwise.dBiCdB(isotropic circular) – the forward gain of an antenna compared to acircularly polarizedisotropic antenna. There is no fixed conversion rule between dBiC and dBi, as it depends on the receiving antenna and the field polarization.dBJenergy relative to 1joule. 1 joule = 1 watt second = 1 watt per hertz, sopower spectral densitycan be expressed in dBJ.dBkdB(kW) – power relative to 1kilowatt.dBKdB(K) – decibels relative tokelvin: Used to expressnoise temperature.dBmdB(mW) – power relative to 1milliwatt.dBm0Power in dBm measured at a zero transmission level point.dBm0sDefined by Recommendation ITU-R V.574.dBmVdB(mVRMS) –voltagerelative to 1 millivolt across 75 Ω.dBodB optical. A change of 1 dBo in optical power can result in a change of up to 2 dBe in electrical signal power in system that is thermal noise limited.dBOsee dBovdBov or dBOdB(overload) – theamplitudeof a signal (usually audio) compared with the maximum which a device can handle beforeclippingoccurs.dBpprelative to the peak to peak sound pressure.dBpprelative to the maximum value of the peak power.dBqdB(quarterwave) – the forward gain of an antenna compared to a quarter wavelength whip. Rarely used, except in some marketing material. 0 dBq = −0.85 dBidBrdB(relative) – simply a relative difference from something else, which is made apparent in context. The difference of a filter's response to nominal levels, for instance.dBrndB abovereference noise. See also dBrnCdBrnCdBrnC represents an audio level measurement, typically in a telephone circuit, relative to thecircuit noise level, with the measurement of this level frequency-weighted by a standard C-message weighting filter. The C-message weighting filter was chiefly used in North America.dBsmdB(m²) – decibel relative to one square meterdBTPdB(true peak) –peak amplitudeof a signal compared with the maximum which a device can handle before clipping occurs.dBu or dBvRMSvoltagerelative to .dBu0sDefined by Recommendation ITU-R V.574.dBuVsee dBμVdBuV/msee dBμV/mdBvsee dBudBVdB(VRMS) –voltagerelative to 1 volt, regardless of impedance.dBVUdB volume unitdBWdB(W) – power relative to 1watt.dBZdB(Z) – decibel relative to Z = 1 mm6⋅m−3dBμsee dBμV/mdBμV or dBuVdB(μVRMS) –voltagerelative to 1 microvolt.dBμV/m, dBuV/m, or dBμdB(μV/m) –electric field strengthrelative to 1microvoltpermeter.

#### Suffixes preceded by a space

dB HLdB hearing level is used inaudiogramsas a measure of hearing loss.dB Qsometimes used to denote weighted noise leveldB SILdBsound intensity level– relative to 10−12 W/m²dB SPLdB SPL (sound pressure level) – for sound in air and other gases, relative to 20 μPa in air or 1 μPa in waterdB SWLdBsound power level– relative to 10−12 W.

#### Suffixes within parentheses

dB(A), dB(B), and dB(C)These symbols are often used to denote the use of differentweighting filters, used to approximate the human ear'sresponseto sound, although the measurement is still in dB (SPL). These measurements usually refer to noise and its effects on humans and other animals, and they are widely used in industry while discussing noise control issues, regulations and environmental standards. Other variations that may be seen are dBAordBA.

#### Other suffixes

dB-HzdB(Hz) – bandwidth relative to one hertz.dB/KdB(K−1) – decibels relative toreciprocalofkelvindBm−1dB(m−1) – decibel relative to reciprocal of meter: measure of theantenna factor.
mBmmB(mW) – power relative to 1milliwatt, in millibels (one hundredth of a decibel). 100 mBm = 1 dBm. This unit is in the Wi-Fi drivers of theLinuxkernel and the regulatory domain sections.
NpAnother closely related unit is theneper(Np). Like the decibel, the neper is a unit oflevel. ## Fractions

Attenuation constants, in fields such as optical fiber communication and radio propagation path loss, are often expressed as a fraction or ratio to distance of transmission. dB/m represents decibel per meter, dB/mi represents decibel per mile, for example. These quantities are to be manipulated obeying the rules of dimensional analysis, e.g., a 100-meter run with a 3.5 dB/km fiber yields a loss of 0.35 dB = 3.5 dB/km × 0.1 km.

• Apparent magnitude

• Cent (music)

• dB drag racing

• Loudness

• One-third octave § Base 10

• pH

• Phon

• Richter magnitude scale

• Sone

## References


Citation Linkdesigntools.analog.comUtilities : VRMS / dBm / dBu / dBV calculator, Analog Devices, retrieved 16 September 2016
Sep 26, 2019, 8:00 AM

Citation Linkopenlibrary.orgIEEE Standard 100: a dictionary of IEEE standards and terms (7th ed.). New York: The Institute of Electrical and Electronics Engineering. 2000. p. 288. ISBN 978-0-7381-2601-2.
Sep 26, 2019, 8:00 AM

Citation Linkwww.iso.org"ISO 80000-3:2006". International Organization for Standardization. Retrieved 20 July 2013.
Sep 26, 2019, 8:00 AM

Citation Linkopenlibrary.orgJohnson, Kenneth Simonds (1944). Transmission Circuits for Telephonic Communication: Methods of analysis and design. New York: D. Van Nostrand Co. p. 10.
Sep 26, 2019, 8:00 AM

Citation Linkbooks.google.comDavis, Don; Davis, Carolyn (1997). Sound system engineering (2nd ed.). Focal Press. p. 35. ISBN 978-0-240-80305-0.
Sep 26, 2019, 8:00 AM

Citation Linkbooks.google.comHartley, R. V. L. (December 1928). "'TU' becomes 'Decibel'". Bell Laboratories Record. AT&T. 7 (4): 137–139.
Sep 26, 2019, 8:00 AM

Citation Linkopenlibrary.orgMartin, W. H. (January 1929). "DeciBel—The New Name for the Transmission Unit". Bell System Technical Journal. 8 (1).
Sep 26, 2019, 8:00 AM

Citation Linkbooks.google.com100 Years of Telephone Switching, p. 276, at Google Books, Robert J. Chapuis, Amos E. Joel, 2003
Sep 26, 2019, 8:00 AM

Citation Linkopenlibrary.orgHarrison, William H. (1931). "Standards for Transmission of Speech". Standards Yearbook. National Bureau of Standards, U. S. Govt. Printing Office. 119.
Sep 26, 2019, 8:00 AM

Citation Link//doi.org/10.1109%2FEE.1954.6438830Horton, J. W. (1954). "The bewildering decibel". Electrical Engineering. 73 (6): 550–555. doi:10.1109/EE.1954.6438830.
Sep 26, 2019, 8:00 AM

Citation Linkwww.bipm.org"Meeting minutes" (PDF). Consultative Committee for Units. Section 3.
Sep 26, 2019, 8:00 AM

Citation Linkwebstore.iec.ch"Letter symbols to be used in electrical technology". International Electrotechnical Commission. 19 July 2002. Part 3: Logarithmic and related quantities, and their units. IEC 60027-3, Ed. 3.0.
Sep 26, 2019, 8:00 AM

Citation Linkphysics.nist.govThompson, A. and Taylor, B. N. sec 8.7, "Logarithmic quantities and units: level, neper, bel", Guide for the Use of the International System of Units (SI) 2008 Edition, NIST Special Publication 811, 2nd printing (November 2008), SP811 PDF
Sep 26, 2019, 8:00 AM

Citation Linkopenlibrary.org"Letter symbols to be used in electrical technology". International Standard CEI-IEC 27-3. International Electrotechnical Commission. Part 3: Logarithmic quantities and units.
Sep 26, 2019, 8:00 AM

Citation Linkopenlibrary.orgMark, James E. (2007). Physical Properties of Polymers Handbook. Springer. p. 1025. […] the decibel represents a reduction in power of 1.258 times […]
Sep 26, 2019, 8:00 AM

Citation Linkopenlibrary.orgYost, William (1985). Fundamentals of Hearing: An Introduction (Second ed.). Holt, Rinehart and Winston. p. 206. ISBN 978-0-12-772690-8. […] a pressure ratio of 1.122 equals + 1.0 dB […]
Sep 26, 2019, 8:00 AM

Citation Linkopenlibrary.orgFedor Mitschke, Fiber Optics: Physics and Technology, Springer, 2010 ISBN 3642037038.
Sep 26, 2019, 8:00 AM

Citation Linkopenlibrary.orgPozar, David M. (2005). Microwave Engineering (3rd ed.). Wiley. p. 63. ISBN 978-0-471-44878-5.
Sep 26, 2019, 8:00 AM

Citation Link//doi.org/10.1088%2F0026-1394%2F38%2F4%2F8I M Mills; B N Taylor; A J Thor (2001), "Definitions of the units radian, neper, bel and decibel", Metrologia, 38 (4): 353, doi:10.1088/0026-1394/38/4/8
Sep 26, 2019, 8:00 AM

Citation Linkopenlibrary.orgR. Hickling (1999), Noise Control and SI Units, J Acoust Soc Am 106, 3048
Sep 26, 2019, 8:00 AM